Fujitsu — forum.xorux.com

Eternus pool History after update

qwexak — Wed, 24 Nov 2021 14:51:23 +0000

Hello!

After update update stor2rrd-7.00 to stor2rrd-7.30 we lost history for pool (io/data/response time/cache/capacity/block size), with volume / drive/ port everything ok.

Perhaps it will help someone, and the backup will be restored in time, we noticed a month later.

Eternus RAID group names and "

martinli — Fri, 28 May 2021 16:31:34 +0000

Hi!

Discovered that if RAID group names contain " then menu json is errored out.

It's allmost as in https://forum.xorux.com/discussion/292/stor2rrd-2-01-json-parse-error

Is it possible that " can be escaped in RAID group names?

Error: No Volumes recognized on DX600S5 - CLI commands have changed

sascha — Thu, 02 Apr 2020 09:11:49 +0000

Hi all,

we have a DX600S5 with Firmware V11L30-1000. No volumes are being recognized and thus the system does not even show up in the menu.

Cause:

FUJITSU Storage ETERNUS login is required. [2020-04-02 09:56:25]
CLI> show volumes -mode detail
                  ^
Error: Invalid parameter.

Apparently the command has changed since on another system with other firmware it works quite well:

CLI> show volumes -mode detail
Volume                                 Status                    Type              Encryption EXC     Expansion       RG or TPP or FTRP     TFOG                 Size(MB)  Size on        Copy       Data      Allocation UID                                       ALUA
No.   Name                                                                                            (Concatenation) No.  Name             No. Name                       RAID Group(KB) Protection Integrity            ID                               Mode
----- -------------------------------- ------------------------- ----------------- ---------- ------- --------------- ---- ---------------- --- ---------------- --------- -------------- ---------- --------- ---------- -------------------------------- -------- ------------------------------
    0 $DEDUP_SYS0                      Available                 TPV(System)       OFF        -                     -    0 TPP_HDD            - -                  8388608              - Disable    Default   Thin                                      - -       -           
    1 $DEDUP_0_0   
...
CLI> show firmware
    Version      Date
 1  V10L86-6000  2019-10-01  Current

What is working on the DX600S5:

FUJITSU Storage ETERNUS login is required. [2020-04-02 09:56:41]
CLI> show volumes
Volume                                 Status                    Type              RG/TPP/FTRP           Size       Data
No.   Name                                                                         No.  Name                        Reduction
----- -------------------------------- ------------------------- ----------------- ---- ---------------- ---------- -----------
    0 $DATA_CNTNR0                     Available                 TPV(System)          0 TPP_HDD           200.00 TB -
    1 Live_GFS_1                       Available                 TPV                  0 TPP_HDD           100.00 TB Dedupe
    2 Live_GFS_2                       Available                 TPV                  0 TPP_HDD           100.00 TB Dedupe

but gives less information and

FUJITSU Storage ETERNUS login is required. [2020-04-02 10:00:58]
CLI> show volumes -detail

Volume No.                      [0]
Volume Name                     [$DATA_CNTNR0]
Status                          [Available]
Type                            [TPV(System)]
RG/TPP/FTRP No.                 [0]
RG/TPP/FTRP Name                [TPP_HDD]
Size                            [200.00 TB(209715200 MB)]
Data Reduction                  [-]
...

but this does not output a table.

Please have a look at what commands need to be changed in eternusconf.pl and eternusperf.pl.

Thanks!

ETERNUS Sample rate

qwexak — Wed, 18 Dec 2019 11:53:16 +0000

Hi.
I am use DX200 S4.

When I tried to add new storage, I received a notification about the error.

SSH data test:NOK

Sample rate is 300sec seconds insted of 300 seconds.

my fix:
config_check.sh:

- sample_rate=`echo "$perform" | grep Interval | cut -d '[' -f 2 | cut -d 'sec]' -f 1'`

+ sample_rate=`echo "$perform" | grep Interval | cut -d '[' -f 2 | cut -d 'sec]' -f 1 | sed 's/sec//g'`

DeviceConnTest.pm:

if ($line =~ m/Interval/){

$line =~ s/Interval//g;

$line =~ s/\[//g;

- $line =~ s/\]//g;

if ($line =~ m/Interval/){

$line =~ s/Interval//g;

$line =~ s/\[//g;

+ $line =~ s/sec\]//g;

ETERNUS DX60 S4

steinweo — Tue, 17 Sep 2019 14:30:54 +0000

Dear,

I recently deployed STOR2RRD 2.52 to monitor our Fujitsu ETERNUS DX60 S4 storage systems. After configuration, everything is running fine, except for the following points under STORAGE >> :

No data under Capacity
No volume under Configuration
No pool in Historical reports
IO missing under POOL
Data missing under POOL
Response time missing under POOL
Cache missing under POOL
Top missing under POOL
Items missing under POOL
The following error is displayed under POOL >> Capacity: "cmd file does not contain data source files: /home/lpar2rrd/stor2rrd/tmp/cvdx60-12/POOL-real-d.cmd /home/lpar2rrd/stor2rrd/bin/detail-graph-cgi.pl:4669"

We have the same behaviour for all six storage systems. It looks like pool information was not fetched correctly.

Could you please help find the right log(s) to look at?

Best regards, Olivier.

connecting to eternus DX90

cja — Wed, 21 Aug 2019 14:16:17 +0000

I'm trying to connect to a Fujitsu eternus DX90 (quite old).
SSH-connect works fine and I can login via ssh as lpar2rrd (appliance).
When I do the config_check it's trying to do this: echo "show performance" | ssh ******
Well, it should work fine, but it doesn't. It seem's that the echo pipe doesn't work from here.
When I login via ssh from the appliance manually it works fine, I can start the show performance.

Maybe it's just a problem with the old firmware, but i cannot cross check this issue.
Any hints here?

Capacity of Tiering Pools

Alex — Tue, 02 Oct 2018 07:14:18 +0000

Hi.
I am use DX200S4, with TPP (Dedup) and FTP.
Capacity incorrect for Flexible Tiering Pools.
I can`t find use command "show show flexible-tier-pools" in scripts files.